Skip to content
The Outlook server is temporarily down. Please send your requests to us on WhatsApp.
Stock is confirmed when you order, and we will advise you as soon as your order is confirmed. Need help with a part? Email orderdesk@kkmsolutions.com.
Ships worldwide — lead time quoted per part orderdesk@kkmsolutions.com
KKM Industrial and Automation Solutions Industrial Automation & MRO Parts Need a part? Email the order desk orderdesk@kkmsolutions.com
Email the order desk Get a quote
Fasteners, Materials & Finishes

Nut Types: Hex, Nylon Insert, Flange and Lock

KKM Solutions · October 21, 2026

A nut must be at least as strong as its bolt: class 8 with 8.8, class 10 with 10.9. Nut types, prevailing torque nuts, jam nuts and material choices.

Nut Types: Hex, Nylon Insert, Flange and Lock — KKM Solutions technical article

Short answer

  • A nut must be at least as strong as its bolt: under ISO 898-2 a class 8 nut matches an 8.8 bolt, class 10 matches 10.9 and class 12 matches 12.9.
  • Prevailing torque nuts resist turning through a nylon insert or deformed thread, but preload, not the locking feature, holds the joint tight.
  • Nylon insert nuts are typically limited to around 120 C; above that use an all-metal lock nut or a castle nut and cotter pin.
  • Neither a lock nut nor threadlocker fixes a joint that loosens because it was under-tightened.

A nut has two jobs: carry the bolt's load through its threads without stripping, and stay where it was put. The first job is about strength class, which has to match the bolt. The second is about how the joint is designed and, sometimes, a locking feature. Most nut problems come from getting the first one wrong or expecting a locking feature to fix a joint that was never tightened properly.

What are the common nut types?

TypeWhat it isTypical use
Hex nutStandard six-sided nut, regular heightGeneral bolting
Heavy hex nutWider across flats and often thicker than a regular nut of the same threadStructural and pressure bolting
Jam (thin) nutReduced-height hex nutLocking against another nut, or where space is short
Nylon insert lock nutHex nut with a nylon ring that grips the bolt threadVibration-prone joints at moderate temperature
All-metal prevailing torque nutLocking from a distorted or crimped thread sectionWhere the nylon insert's temperature limit is a problem
Flange nutHex nut with a built-in washer face, plain or serratedSpreading load, oversized or slotted holes
Castle or slotted nutSlots that take a cotter pin through a drilled boltPositive retention, often on axles and linkages
Coupling nutLong nut joining two threaded rodsExtending threaded rod
Cap (acorn) nutDomed nut covering the bolt endCovering exposed thread

How does a nut grade or property class match the bolt?

The rule is that the nut must be at least as strong as the bolt, so that the bolt, not the nut thread, is the weak link. A stripped nut thread can fail without warning, while a bolt yielding first at least behaves predictably.

  • Metric: nut property classes are set by ISO 898-2. A class 8 nut matches an 8.8 bolt, class 10 matches 10.9 and class 12 matches 12.9. The class number is usually stamped on the nut.
  • Inch: SAE J995 Grade 5 nuts go with SAE J429 Grade 5 bolts and Grade 8 nuts with Grade 8 bolts. ASTM A563 nuts (Grade DH, for example) are the common choice with ASTM structural and high-strength bolts; check the bolt specification for which nut grade it calls for.

A stronger nut can generally go on a weaker bolt, but never the reverse. ISO 898-2 nuts are specified for use within a set temperature range; outside it, their properties are not guaranteed, which is one reason high-temperature bolting uses its own specifications such as ASTM A194 nuts.

What is a prevailing torque nut and can it be reused?

A prevailing torque nut resists turning even before it touches the joint, because something in the nut grips the bolt thread: a nylon insert, or a deformed metal section. That resistance is called prevailing torque. It keeps the nut from backing off if preload is lost, but it is not what holds the joint tight. Preload does that.

Two practical consequences:

  • Tightening torque. Some of the torque you apply goes into overcoming the prevailing torque, not into clamping. Torque values for prevailing torque nuts should come from the nut or equipment maker.
  • Reuse. The locking element wears each time the nut is run on and off. Guidance on how many reuses are acceptable varies by maker and product. For any joint where loosening would be a safety issue, fit a new nut. If you do reuse one, it should still require noticeable effort to turn by hand on the thread; if it spins freely, it has lost its locking function.

Nylon insert nuts have a temperature limit set by the nylon, typically around 120 °C, though some grades go higher. Check the maker's data. Above that, use an all-metal prevailing torque nut or a mechanical method such as a castle nut and cotter pin.

How do flange, serrated and jam nuts work?

Flange nuts carry their own washer face, which spreads the clamp load over a bigger area. That helps on soft materials, slotted holes and oversized holes, and saves a loose washer.

Serrated flange nuts add small teeth on the bearing face that bite into the clamped surface and resist turning. They work by marking the surface, so they will damage paint, plating and soft surfaces, and they are not meant to be used over a separate washer. Whether they suit hardened surfaces depends on the product; check the maker's guidance.

Jam nuts are thin nuts used in pairs with a full nut to lock a position, typically on adjusting rods and tensioners. The usual method is to run the thin nut on first and tighten it, then run the full nut down, hold the thin nut with a wrench and tighten the full nut against it. Practice and torque splits vary, and on a critical joint the equipment maker's instruction governs. Putting the thin nut on top of a full nut is generally considered incorrect, because the thin nut then carries the load.

When should you use a lock nut instead of threadlocker?

Both resist loosening; they do it differently.

Prevailing torque lock nutLiquid threadlocker
How it worksMechanical grip on the threadAdhesive cures in the thread gaps
Ready to useImmediatelyAfter it cures
Thread conditionTolerant of oily threadsNeeds clean threads for full strength, per the product's instructions
AdjustmentHolds an adjusted position, such as a set clearanceBest where the nut is tightened down fully
RemovalSpanner, with some extra effortDepends on strength grade; high-strength grades may need heat

A lock nut makes sense where the nut sets a position rather than clamping hard, where the joint is taken apart often, or where you cannot clean and cure. Threadlocker suits clean threads in fully tightened joints and also seals the thread. Neither fixes a joint that loosens because it was under-tightened or because the clamped parts slip sideways. Get the preload right first.

Which nut materials suit heat and corrosion?

  • Carbon and alloy steel, plain or plated (zinc and others). Most general bolting. The plating sets the corrosion resistance.
  • Stainless steel. Metric stainless fasteners are graded under ISO 3506, with A2 and A4 the common grades (A4 is the molybdenum-bearing grade often chosen for chloride exposure). Stainless on stainless can gall during tightening; anti-seize and lower speeds help.
  • High-temperature bolting. Pressure and high-temperature joints use nuts to their own specifications, such as ASTM A194, matched to the stud material.
  • Brass and nylon for electrical, non-magnetic or very light-duty uses.

Mixing a stainless nut with a plated steel bolt, or either with aluminium parts, can set up galvanic corrosion in a wet environment. Match the nut material to the bolt and to the service.

How do you identify a nut you need to match?

  • Thread size and pitch. Check with a thread gauge or a known bolt. Metric coarse and fine, and inch UNC and UNF, look alike at a glance.
  • Width across flats and height. These tell regular, heavy and jam nuts apart.
  • Markings. Property class or grade marks on the face or flats, and any maker's mark.
  • Locking feature. Nylon ring, distorted thread, serrations or slots.
  • Material and finish. A magnet helps separate most carbon steel from austenitic stainless, though cold-worked stainless can be slightly magnetic.

Further reading on this site: bolt property classes and grades; washer types; thread locking and anti-seize; bolt torque calculator; galvanic corrosion and dissimilar metals.

If you need nuts to match a particular bolt grade or a maker's original fastener, send us the bolt specification, thread size and the service conditions, and we will source the matching nut class and type for you.

Need a quote on a specific part?

Our order desk replies within 1 business day. No account needed. Or email orderdesk@kkmsolutions.com.

Request a Quote

Frequently asked questions

Which nut goes with an 8.8 or 10.9 bolt?

Under ISO 898-2, a property class 8 nut matches an 8.8 bolt, class 10 matches 10.9 and class 12 matches 12.9. For inch fasteners, SAE J995 Grade 5 nuts go with Grade 5 bolts and Grade 8 nuts with Grade 8. A stronger nut can generally go on a weaker bolt, but never the reverse.

Can nylon insert lock nuts be reused?

The locking element wears each time the nut is run on and off, and reuse guidance varies by maker. For any joint where loosening would be a safety issue, fit a new nut. If you reuse one, it should still need noticeable effort to turn on the thread; if it spins freely it has lost its locking function.

What temperature can a nylon insert nut take?

The nylon sets the limit, typically around 120 C, although some grades go higher, so check the maker's data. Above that limit, use an all-metal prevailing torque nut, which locks through a distorted or crimped thread section, or a mechanical method such as a castle nut with a cotter pin.

How do you install a jam nut correctly?

The usual method is to run the thin jam nut on first and tighten it, then run the full nut down, hold the thin nut with a wrench and tighten the full nut against it. Practice and torque splits vary, and the equipment maker's instruction governs on a critical joint. A thin nut on top of a full nut is generally considered incorrect.