Bolt Property Classes and Grades: Reading the Head Marking
Short answer
- Bolt head markings are standardized shorthand for a fastener's mechanical properties, and metric property classes such as 8.8, 10.9 and 12.9 are read by multiplying the first number by 10 to get nominal tensile strength in MPa.
- SAE grades equal the number of radial lines plus two, so three lines mark Grade 5 and six lines mark Grade 8, while a stainless A2-70 bolt sits below metric Class 8.8 in strength.
- Mixing grades in one joint is dangerous because a weaker nut strips or a lower-grade bolt yields first, so the nut must always be at least as strong as the bolt.
You are staring at a bolt head covered in numbers and radial lines, trying to determine if it can hold the load on your machinery. Those markings are not arbitrary; they are a standardized shorthand indicating the fastener's mechanical properties. Selecting or substituting the wrong grade can lead to rapid joint failure, so understanding how to read these designations is critical for any maintenance or reliability engineer.
How do you read metric property classes like 8.8 and 10.9?
Metric fasteners use a two-part numbering system separated by a decimal point, known as the property class. The formula is straightforward: multiply the first number by 10 to get the nominal tensile strength in megapascals (MPa). The second number represents the yield-to-tensile ratio. Multiply the two numbers together, then by 10, to get the nominal yield strength in MPa.
Let us break down the most common high-strength metric classes:
- Class 8.8: Nominal tensile strength is 8 x 10 = 800 MPa. Yield strength is 8 x 8 x 10 = 640 MPa.
- Class 10.9: Nominal tensile strength is 10 x 10 = 1,000 MPa. Yield strength is 10 x 9 x 10 = 900 MPa.
- Class 12.9: Nominal tensile strength is 12 x 10 = 1,200 MPa. Yield strength is 12 x 9 x 10 = 1,080 MPa.
Class 8.8 bolts are typically medium carbon steel, quenched and tempered. Classes 10.9 and 12.9 are made from alloy steels and undergo similar heat treatment to achieve their higher strength limits. When sourcing metric fasteners and hardware, you must match the property class to the original design specification, as substituting a lower class drastically reduces the clamp load the joint can sustain before yielding.
How do you read SAE and ASTM bolt head markings?
Imperial (inch-series) fasteners use radial lines on the bolt head to indicate SAE grades, while ASTM grades typically use a combination of letters and numbers. The rule for SAE bolts is that the grade is equal to the number of radial lines plus two. The lines are raised, not stamped, and must be counted carefully.
- SAE Grade 2: No head markings. These are low or medium carbon steel bolts with a tensile strength around 60,000 to 74,000 psi depending on diameter. They are general-purpose fasteners, not for high-strength structural applications.
- SAE Grade 5: Three radial lines. Made of medium carbon steel, quenched and tempered, with a tensile strength of roughly 120,000 psi (for 1-inch and under). Common in automotive and general machinery.
- SAE Grade 8: Six radial lines. Medium carbon alloy steel, quenched and tempered, delivering a tensile strength of about 150,000 psi. These are the standard high-strength imperial bolts for heavy industrial applications.
For structural applications, ASTM designations take precedence. ASTM A325 and ASTM A490 bolts are designed for structural steel connections. A325 bolts have a tensile strength of 120,000 psi (for bolts up to 1 inch) and are marked with three radial lines, similar to SAE Grade 5. A490 bolts offer 150,000 psi tensile strength and are marked with six lines, but they are made from alloy steel and have specific atmospheric corrosion resistance requirements. ASTM A307 bolts are low-carbon steel (similar to SAE Grade 2) and marked with an A307 stamp, used for general non-structural applications.
Are A2 and A4 stainless bolts high-strength fasteners?
Stainless steel fasteners use a different designation system entirely. You will typically see an A-number followed by a dash and a two-digit number indicating the tensile strength in MPa divided by 10. The two common grades are A2 (roughly equivalent to 304 stainless) and A4 (roughly equivalent to 316 stainless, with added molybdenum for better pitting corrosion resistance).
An A2-70 bolt has a nominal tensile strength of 700 MPa. An A4-80 bolt has a nominal tensile strength of 800 MPa. The critical detail here is that stainless steel is not a high-strength fastener class. A standard A2-70 bolt sits below metric Class 8.8 in terms of tensile and yield strength.
Furthermore, austenitic stainless steels (the 300 series) cannot be hardened by heat treatment. They are strengthened only through cold working, which is why their strength ceiling is relatively low. If your application requires high strength and corrosion resistance, standard 304 or 316 stainless will not suffice. You must look to specialized alloys, precipitation-hardening stainless, or coated carbon steel. Assuming a stainless bolt is equivalent to a Class 10.9 or SAE Grade 8 because it looks shiny and expensive is a fast track to a catastrophic failure.
Why is mixing fastener grades in one joint dangerous?
Why is mixing grades in a single joint so dangerous? It comes down to how a bolted joint achieves clamp load. When you tighten a bolt, you are stretching the bolt to create tension, which in turn compresses the joint members. The fastener acts like a spring.
If you mix a Grade 5 bolt with a Grade 2 nut, the nut threads will strip or yield long before the bolt reaches its required tension. The bolt's tensile strength is wasted because the nut fails first. The general rule is that the nut must always be at least as strong as the bolt. Standard hex nuts have their own grade designations that correspond to bolt grades. Using a standard nut with a high-strength bolt is a common failure point.
Conversely, if you replace one bolt in a flanged joint with a lower grade, that single bolt will yield under the same torque value applied to the higher-grade bolts. Once it yields, it loses its clamp load, shifting the entire load profile to the adjacent bolts. This cascading failure can cause the gasket to blow out or the flange to slip. When assembling structural framing hardware and connectors, every fastener in a shear or tension joint must have identical mechanical properties to ensure even load distribution.
How do lubrication and torque affect bolt clamp load?
Reading the bolt head is only the first step; applying the correct torque is the second. Torque charts are based on specific friction coefficients. If you take a dry, unlubricated torque value from an SAE Grade 5 chart and apply it to a lubricated Grade 8 bolt, you will over-tension the bolt and risk snapping it.
Friction determines how much of your input torque converts to bolt tension rather than just overcoming thread friction. A dry zinc-plated bolt might have a friction coefficient of 0.20, while a heavily lubricated bolt could drop to 0.12. Applying the same torque value to both will result in significantly more clamp load in the lubricated bolt—potentially exceeding its yield point. Always verify if your torque specification assumes dry or lubricated threads. If the joint requires anti-seize or thread locker, you must use the torque values corresponding to that specific lubrication condition. You can source the necessary adhesives, sealants and chemicals to control these friction variables, but you must adjust your torque wrench accordingly.
Using the correct tools is equally important. A torque wrench that is out of calibration will stretch a bolt incorrectly regardless of your math. Ensure your hand tools are up to the task and calibrated if they feature torque measurement capabilities.
How should high-strength bolts be installed safely?
High-strength fasteners store a significant amount of potential energy. If a Grade 8 or Class 12.9 bolt fails during installation due to over-torque, it can snap violently, sending shrapnel across the work area. All torque application on high-strength fasteners must be performed by qualified personnel using the correct personal protective equipment. Ensure your face and hands are clear of the direct line of the bolt axis when applying final torque.
Inspect bolt heads before installation. If the radial lines are worn off or the head is damaged, you cannot verify the grade. Discard unidentifiable fasteners. A bolt without a legible grade marking is a structural unknown and has no place in a loaded assembly.
If you need help sourcing specific metric property classes, imperial SAE grades, or matching nut-and-bolt assemblies, our team can cross-reference your requirements and source the correct components for your application.
Need a quote on a specific part?
Request a QuoteFrequently asked questions
How do you calculate bolt strength from a metric property class like 10.9?
Multiply the first number by 10 to get nominal tensile strength in megapascals. For Class 10.9, that is 10 x 10 = 1,000 MPa. The second number is the yield-to-tensile ratio, so multiplying 10 x 9 x 10 gives a nominal yield strength of 900 MPa.
How can you tell an SAE Grade 5 bolt from a Grade 8 by the head?
Count the raised radial lines on the head and add two. Three radial lines mark SAE Grade 5, a medium carbon steel bolt with roughly 120,000 psi tensile strength for 1-inch and under. Six lines mark Grade 8, a medium carbon alloy steel bolt delivering about 150,000 psi tensile strength.
Is stainless steel as strong as a Class 8.8 or Grade 8 bolt?
No, stainless steel is not a high-strength fastener class. A standard A2-70 bolt has a nominal tensile strength of 700 MPa and sits below metric Class 8.8 in tensile and yield strength. Austenitic 300 series stainless cannot be hardened by heat treatment, so it is strengthened only through cold working.
Can you mix a Grade 5 bolt with a Grade 2 nut?
No, because the nut threads will strip or yield long before the bolt reaches its required tension, wasting the bolt's tensile strength. The general rule is that the nut must always be at least as strong as the bolt. Replacing one bolt in a flanged joint with a lower grade also lets that bolt yield and shifts load to adjacent bolts.
Industrial Automation & MRO Parts