Skip to content
The Outlook server is temporarily down. Please send your requests to us on WhatsApp.
Stock is confirmed when you order, and we will advise you as soon as your order is confirmed. Need help with a part? Email orderdesk@kkmsolutions.com.
Ships worldwide — lead time quoted per part orderdesk@kkmsolutions.com
KKM Industrial and Automation Solutions Industrial Automation & MRO Parts Need a part? Email the order desk orderdesk@kkmsolutions.com
Email the order desk Get a quote
Design Calculations & Reference

ISO Tolerances and Fits: Reading H7/g6

KKM Solutions · August 11, 2026

Decoding the ISO limits-and-fits system: how letter codes define tolerance zone position and IT grades define width, and why H7/g6 creates a precise running.

ISO Tolerances and Fits: Reading H7/g6 — KKM Solutions technical article

Short answer

  • An ISO fit like H7/g6 combines a letter that sets the position of the tolerance zone relative to nominal diameter with an IT grade number that sets the width of that zone.
  • Uppercase letters apply to holes and lowercase letters apply to shafts, so H7 is a hole whose lower limit is exactly nominal and g6 is a shaft whose upper limit sits below nominal, ensuring clearance.
  • Clearance, transition and interference fits are the three families, and surface finish and temperature can change the fit actually achieved in assembly.

You are looking at a drawing that specifies an H7/g6 fit for a shaft and hole, and you need to know exactly what clearance to expect when the parts arrive. The ISO limits-and-fits system is a shorthand for communicating exactly how two mating parts will interact, but only if you understand the physical meaning behind the letters and numbers.

How does an ISO tolerance code work?

An ISO fit designation like H7/g6 consists of three pieces of information: a letter, a number, and the case of the letter. The letter establishes the fundamental deviation, which is the position of the tolerance zone relative to the nominal diameter. The number is the IT (International Tolerance) grade, which defines the total width of the tolerance zone. Uppercase letters always apply to holes (internal features), and lowercase letters always apply to shafts (external features).

For the H7 hole, the uppercase 'H' means the fundamental deviation is zero. The lower limit of the hole is exactly the nominal diameter, and the upper limit is nominal plus the IT7 tolerance width. A 25mm H7 hole, for example, has a tolerance zone of 0 to +0.021 mm. The lowercase 'g' on the shaft indicates a negative fundamental deviation. The upper limit of the shaft sits below the nominal diameter, guaranteeing a clearance gap before you even account for the tolerance width. The '6' designates an IT6 tolerance width, which is narrower than the IT7 hole tolerance.

As a rule of thumb, the IT grade widens as the nominal diameter increases, but the standard ensures the relative precision remains consistent across the size range.

Why use a hole-basis system instead of shaft-basis?

The vast majority of industrial designs use a hole-basis system, which is why you see 'H' as the first letter in standard fits. The reason is purely practical: producing an internal feature to an exact size is generally more difficult and costly than producing an external feature. By standardizing the hole at 'H' (where the lower limit is exactly nominal), you can use a standard reamer or boring tool to create the hole, and then machine the shaft to whatever tolerance is required to achieve the desired fit class.

A shaft-basis system (using 'h' as the baseline) is used occasionally, typically when a raw shaft material is supplied to a specific tolerance and the designer must match the mating components to it. This is common in linear shafts and ball bushings, where the shafting is often supplied precision-ground to a standard h-tolerance, and the mating bushings are selected to provide the necessary running clearance.

What are the three ISO fit families?

By mixing different fundamental deviations, you create three distinct families of fits. Each family dictates the physical assembly method and the operational behavior of the joint.

Clearance Fits

In a clearance fit, the largest possible shaft is always smaller than the smallest possible hole. The parts will assemble by hand. The H7/g6 fit is a classic precision running fit. Because the 'g' shaft has a negative fundamental deviation, it guarantees a small, consistent clearance. This makes it ideal for applications requiring accurate location with free running, such as sliding spindles, precision guide pins, or lightly loaded journal bearings.

An H7/f7 fit provides more clearance, making it better for higher-speed rotation where thermal expansion might close the gap, or where lubrication requires more room to form a hydrodynamic film.

Transition Fits

Transition fits like H7/k6 or H7/n6 are where the tolerance zones overlap. Depending on where the actual machined dimensions land within their allowed bands, you might get a slight interference or a slight clearance. An H7/k6 fit will usually require light tapping with a mallet to assemble and provides accurate location with minimal play. An H7/n6 fit leans toward interference and is used for more permanent locating assemblies where you want to eliminate vibration but do not want the extreme stresses of a heavy press fit.

Interference Fits

Interference fits, such as H7/p6 or H7/s6, guarantee that the smallest possible shaft is larger than the largest possible hole. The parts cannot be assembled by hand. An H7/p6 fit is a standard press fit, often assembled with a hydraulic press. An H7/s6 fit requires heavy pressing or thermal assembly—heating the hole housing or freezing the shaft with liquid nitrogen to temporarily reverse the interference for assembly. These fits are used to transmit torque without keys, relying entirely on the friction generated by the radial clamping force of the interference.

Which bearing ring needs an interference fit?

Rolling element bearings require specific fits on their inner and outer rings, and the choice depends entirely on what the bearing is doing. The critical concept here is the rotating-load ring. If a ring rotates relative to the direction of the applied load, it must have an interference fit on its mating surface. If a ring is stationary relative to the load, it can have a clearance fit.

Consider an electric motor where the shaft rotates and the housing is stationary, with the load direction remaining constant (pointed downward by gravity). The inner ring rotates with the shaft and relative to the load. This is a rotating-load ring. If you were to clear-fit the inner ring to the shaft, the ring would slowly creep around the shaft circumference, causing fretting wear and destroying the shaft seat. To prevent this, the inner ring requires an interference fit, typically k5 or m5 on the shaft.

Conversely, the outer ring is stationary relative to the load. It can be clear-fit into the housing, typically H7 or H6. This allows for thermal expansion and makes bearing replacement easier. If the outer ring were the rotating-load ring, such as in a hub arrangement where the wheel rotates around a stationary axle, the outer ring would need the interference fit in the housing, and the inner ring could be clear-fit on the axle.

How do surface finish and temperature change a fit?

A drawing may specify an H7/s6 interference fit, but the physical assembly will only achieve that fit if the surface finish and operating temperature cooperate. The tolerance zones assume smooth geometries. When you press a shaft into a housing, the surface peaks of the machined profiles crush and shear. If the surface roughness is high, the actual interference achieved after assembly will be less than the calculated dimensional interference. A coarse turned finish might lose a significant portion of its effective interference simply by deforming the surface asperities. For heavy press fits, you need ground surfaces to ensure the calculated interference translates into actual clamping force.

Temperature differentials also alter fits dynamically. A steel shaft in an aluminum housing assembled with an interference fit will loosen as temperature rises, because aluminum expands at roughly twice the rate of steel. Conversely, in a high-speed ball bearing application, the inner ring heats up faster and expands more than the outer ring, potentially reducing the internal clearance of the bearing and causing thermal seizure if the initial clearances were not calculated for the operating temperature.

When standard press fits are not practical for maintenance or thermal expansion reasons, you can use bearing adapters, sleeves and lock nuts to secure rotating-load rings on straight shafts without machining interference tolerances. For power transmission applications where you need to mount pulleys or sprockets to a shaft, bushings and hubs provide a tapered interference that can be tightened and released without a hydraulic press.

If you need help sourcing or cross-referencing components for a specific ISO fit, our team can assist with identifying compatible bearings, bushings, or shafting for your application requirements.

Need a quote on a specific part?

Our order desk replies within 1 business day. No account needed. Or email orderdesk@kkmsolutions.com.

Request a Quote

Frequently asked questions

What does H7/g6 mean on a drawing?

H7/g6 specifies a precision running fit with clearance between a hole and a shaft. The uppercase H7 hole has a fundamental deviation of zero, so its lower limit is exactly the nominal diameter and its upper limit is nominal plus the IT7 tolerance width. The lowercase g6 shaft has a negative fundamental deviation, so its upper limit sits below nominal, ensuring a small, consistent clearance.

How do you tell a hole tolerance from a shaft tolerance in the ISO system?

The case of the letter tells you. Uppercase letters always apply to holes, meaning internal features, and lowercase letters always apply to shafts, meaning external features. The letter gives the fundamental deviation, which positions the tolerance zone relative to the nominal diameter, while the number gives the IT grade, which defines the total width of the tolerance zone.

Why do most industrial designs use a hole-basis system?

Producing an internal feature to an exact size is generally more difficult and costly than producing an external feature. With the hole standardized at H, where the lower limit is exactly nominal, a standard reamer or boring tool can create the hole, and the shaft is then machined to whatever tolerance achieves the desired fit class. A shaft-basis system using h is used only occasionally.

What fit does a bearing inner ring need on a rotating shaft?

A bearing ring that rotates relative to the direction of the applied load, called a rotating-load ring, must have an interference fit on its mating surface. In an electric motor with a rotating shaft and a constant load direction, the inner ring typically takes k5 or m5 on the shaft. A clearance fit would let the ring creep around the shaft, causing fretting wear.