Roller Chain: ANSI/ISO Designation and Selection
Short answer
- Roller chain should be selected by power rating and service factor rather than by breaking load, because breaking load is a static failure metric that says nothing about dynamic fatigue life.
- The ANSI number encodes pitch in eighths of an inch, and pitch, roller diameter and inner width must all match the sprocket for the chain to engage properly.
- Industrial chain is typically replaced at 2% elongation, a worn chain should always be replaced together with its sprockets, and lubrication method should be matched to chain speed.
A roller chain drive fails progressively, not catastrophically. When it does fail, the root cause is usually misapplication—selecting the chain by breaking load rather than by power rating, or ignoring the wear elongation limit until the chain destroys the sprockets. Understanding the ANSI and ISO designation systems, and the physical dimensions that govern interchangeability, is the prerequisite for specifying the correct drive or conveyor chain and keeping it running.
How do ANSI and ISO roller chain designations work?
The American National Standards Institute (ANSI) system uses a two- or three-digit number to encode the chain's physical characteristics. The governing rule is that the first digit (or first two digits, for chains with a pitch of 1 inch or greater) represents the chain pitch in eighths of an inch. The trailing digit indicates whether the chain is a standard roller chain or a bushing chain.
For example, a standard ANSI No. 60 chain has a pitch of 6/8 inch (0.75 inches). A No. 40 chain has a pitch of 4/8 inch (0.50 inches). The trailing zero signifies a standard roller chain, meaning it has freely rotating rollers over the bushings. A trailing 5 indicates a bushing chain, which lacks rollers (e.g., ANSI No. 55). Bushing chains are typically used in low-speed, high-load applications where the rolling friction of a standard roller chain is unnecessary, or in specific conveyor environments.
An H suffix denotes a heavy series chain (e.g., ANSI No. 60H). Heavy series chains utilize thicker link plates than standard chains of the same pitch. They are designed for high-load, low-speed drives where shock loads are prevalent. The thicker plates increase the chain's tensile strength and fatigue resistance, though they do not increase the roller diameter or pitch dimensions.
Multi-strand chains are designated by adding a hyphen and the number of strands before the chain number (e.g., 2-60 for double-strand, 3-60 for triple-strand). Multi-strand chains multiply the power capacity of a single strand by a factor of roughly 1.7 for double-strand and 2.5 for triple-strand, accounting for the unequal load distribution inherent in multi-strand drives.
The International Organization for Standardization (ISO) designates chains by pitch multiplied by 16 (converting inches to millimeters via a factor of 25.4/1.6) followed by a B for bushing chain or a standard roller chain designation. For instance, an ISO 12B chain corresponds to an ANSI No. 60 chain in pitch. However, ANSI and ISO chains are not strictly interchangeable. While the pitch may be similar, the roller diameters and inner plate widths often differ. When sourcing chains and sprockets, you must verify the exact dimensional standard to ensure the chain will seat properly in the sprocket tooth gap.
Which three dimensions decide chain and sprocket fit?
Three dimensions define whether a chain will function on a given sprocket: pitch, roller diameter, and inner width. If any of these deviate from the sprocket's design parameters, the chain will either fail to engage the sprocket or wear out prematurely.
- Pitch: The distance from the centerline of one pin to the centerline of the next pin. This must exactly match the sprocket tooth spacing. A mismatch here causes the chain to ride up or bind on the sprocket teeth.
- Roller diameter: The outside diameter of the roller. This must match the sprocket's tooth gap bottom. An oversized roller will bottom out and bind; an undersized roller will cause point loading and rapid wear.
- Inner width: The distance between the inner link plates. This must clear the sprocket tooth thickness. If the inner width is too narrow, the chain will pinch the sprocket; if it is too wide, the chain will wander laterally and potentially derail.
Always cross-reference these three dimensions when substituting brands. A chain with the correct pitch but an incorrect roller diameter will destroy a sprocket in short order.
How do you select a roller chain by service factor?
The most common selection error is choosing a chain based on its ultimate tensile strength (breaking load). Breaking load is a static failure metric that tells you nothing about the dynamic fatigue life of the chain under operating conditions. A chain with a high breaking load but insufficient fatigue strength will still fail rapidly in a high-cycle drive.
Correct selection uses the chain manufacturer's power rating tables. These tables list the maximum horsepower a chain can transmit at a given speed, based on the pin and bushing wear limits, not the tensile strength of the plates. To use these tables, first calculate the required service factor.
The service factor accounts for the shock loading and duty cycle of the application. A uniform load, such as a centrifugal pump driven by an electric motor, might use a service factor of 1.0. A moderate shock load, like a conveyor drive, might require 1.4. A heavy shock load, such as a crusher or reciprocating pump, can require a service factor of 2.0 or higher.
Multiply the motor nameplate horsepower by the required service factor to get the design horsepower. Then, enter the manufacturer's power rating table with the design horsepower and the speed of the small sprocket (RPM) to find the minimum chain size that meets or exceeds the requirement. If the design horsepower falls between two chain sizes, select the larger size. This method ensures the chain is selected based on its ability to withstand dynamic wear and fatigue over time, not its ability to survive a one-time static pull.
When should roller chain and sprockets be replaced?
Roller chain wear occurs between the pin and the bushing. As this wear progresses, the bushings elongate the pitch of the chain. This elongation causes the chain to climb higher on the sprocket teeth, eventually reaching the tooth tip. The standard replacement threshold for industrial roller chain is 2% elongation. For precision drives, this limit is often 1%.
To measure elongation, measure a specific number of chain pitches (e.g., 12 pitches) under slight tension. Compare this measurement to the theoretical length of those pitches (12 x pitch). The percentage difference is the elongation. For a No. 60 chain (0.75 inch pitch), 12 pitches should measure 9.00 inches. At 2% elongation, the measurement would be 9.18 inches. Replace the chain before it exceeds this limit.
A worn chain must always be replaced together with its sprockets. A worn sprocket has a hooked or cupped tooth profile. If you install a new chain on a worn sprocket, the new chain will not seat properly in the worn tooth gaps. The new chain pins and rollers will be subjected to extreme point loading and stress concentrations, causing the new chain to stretch rapidly to match the worn sprocket's pitch, often within a fraction of its expected lifespan. Installing a new chain on a worn sprocket is a guaranteed way to waste a new chain.
How should roller chain be lubricated at each speed?
Lubrication is the single most critical factor in achieving the rated life of a power transmission chain. The lubricant must penetrate the pin and bushing clearance to create a hydrodynamic film. Without this film, metal-on-metal contact causes rapid adhesive wear. The lubrication method required depends on the chain speed.
- Manual or drip lubrication: Used for low-speed drives (up to 600 ft/min). Oil is applied directly to the chain with a brush or drip feeder. This is suitable for drives that are not enclosed.
- Bath or disc lubrication: Used for medium-speed drives (up to 2,000 ft/min). The chain dips into an oil bath in the drive casing, or a disc attached to the shaft picks up oil and deposits it on the chain. This requires an enclosed oil-tight casing.
- Stream lubrication: Used for high-speed drives (over 2,000 ft/min). A pump continuously delivers a stream of oil directly to the inside of the chain loop, where it flows across the pins and rollers. This method also provides cooling, which is essential at high speeds.
Using the correct lubricant is just as important as the delivery method. High-speed drives require a clean, medium-viscosity oil to penetrate the clearances, not a heavy grease. Grease is generally too viscous to penetrate the pin-bushing clearance and will starve the joint of lubrication. When specifying lubricants and lubrication systems, consult the chain manufacturer's viscosity recommendations based on the ambient temperature and chain speed.
What conveyor chain variants are available?
Standard power transmission roller chain is designed to wrap around sprockets. In material handling, chains often serve as the conveying medium itself, requiring specific geometries and materials. When sourcing conveyor chain and belting, you will encounter several specialized variants.
Attachment chains feature extended pins or bent or extended link plates with holes. These attachments provide mounting points for flights, slats, buckets, or custom fixtures. The attachments are designated by a letter and number system (e.g., A-1, K-2). An A-1 attachment has one extended pin with a single hole, while a K-2 attachment has a bent extended plate with two holes. The spacing and type of attachments must match the conveying fixture geometry exactly.
Hollow pin chains use link plates with hollow pins rather than solid pins. This allows a cross-rod or pin to pass completely through the chain at any pitch, making it ideal for supporting wide conveyor belts or for applications where fixtures must pivot on the cross-rod. Hollow pin chains are common in food processing and packaging conveyors.
Stainless steel chains are used in corrosive environments, such as food processing, chemical plants, and outdoor applications. They are typically manufactured from 300-series or 400-series stainless steel. While stainless steel offers excellent corrosion resistance, it has lower tensile strength and lower surface hardness than carbon steel. Consequently, a stainless steel chain will have a lower power rating and a higher wear rate than a carbon steel chain of the same size. It must be selected with a higher service factor to compensate for its lower load-carrying capacity. Manufacturers like Rexnord produce specialized stainless and corrosion-resistant conveyor chains engineered for these specific harsh-environment applications.
Whether you are cross-referencing an ANSI 60H drive chain or specifying a stainless attachment chain for a washdown conveyor, KKM Industrial can source the exact chain, sprockets, and lubricants your application requires. Contact our team for assistance with cross-referencing and selecting the correct components.
Need a quote on a specific part?
Request a QuoteFrequently asked questions
What does an ANSI roller chain number mean?
The first digit, or first two digits for chains with a pitch of 1 inch or greater, gives the chain pitch in eighths of an inch. The trailing digit shows the type: a zero means standard roller chain and a 5 means bushing chain without rollers. For example, a No. 60 chain has a pitch of 6/8 inch, or 0.75 inches. An H suffix marks a heavy series chain with thicker link plates.
How do you select a roller chain for a drive?
Select by the manufacturer's power rating tables, not by breaking load. Multiply motor nameplate horsepower by the service factor to get design horsepower, then enter the table with that figure and the small sprocket speed in RPM. If the design horsepower falls between two chain sizes, choose the larger size. Service factors run from 1.0 for uniform loads to 1.4 for conveyors and 2.0 or higher for heavy shock.
When should a roller chain be replaced?
Industrial roller chain is typically replaced at 2% elongation, and precision drives often use a 1% limit. Elongation is measured over a set number of pitches, such as 12, under slight tension. For a No. 60 chain, 12 pitches should measure 9.00 inches new and 9.18 inches at 2% elongation. A worn chain must be replaced together with its sprockets.
Can ANSI and ISO roller chains be interchanged?
No, ANSI and ISO chains are not strictly interchangeable. The pitch may be similar, but roller diameters and inner plate widths often differ. Fit on a sprocket depends on pitch, roller diameter and inner width, and any deviation means the chain will fail to engage or wear out prematurely. Verify the exact dimensional standard so the chain seats properly in the sprocket tooth gap.
Industrial Automation & MRO Parts