Pneumatic and Electric Grippers: Sizing Grip Force and Stroke
Short answer
- Grip force for an industrial gripper is sized from part weight, friction, acceleration and a safety factor, while stroke must cover part size and tolerance.
- A 10 kg part with a 0.3 friction coefficient, held by two fingers under 1G of acceleration, needs 327 N per finger before a safety factor, which becomes 654 N at 2x.
- Pneumatic grippers give high force and fast cycles, electric grippers give precise force and position control, and longer fingers reduce usable force through derating.
When selecting an industrial gripper, the primary considerations are grip force and stroke. Grip force must account for part weight, friction, acceleration, and safety factors, while stroke must accommodate part size and tolerance. This article covers the engineering principles for sizing both pneumatic and electric grippers.
How do you calculate the grip force a gripper needs?
The required grip force depends on the part's weight, the coefficient of friction between the gripper fingers and the part, and any dynamic forces from acceleration. The basic equation for grip force is:
Grip Force (Fgrip) = (Part Weight + Acceleration Force) / (Coefficient of Friction × Number of Fingers)
For example, consider a part weighing 10 kg with a coefficient of friction of 0.3, being gripped by two fingers. If the part experiences 1G of acceleration:
- Acceleration Force = 10 kg × 9.81 m/s² × 1 = 98.1 N
- Total Force = 10 kg × 9.81 m/s² + 98.1 N = 196.2 N
- Grip Force per Finger = 196.2 N / (0.3 × 2) = 327 N
A safety factor is then applied. For horizontal applications, a factor of 2x is common, while higher factors (3x-5x) may be needed for vertical or high-acceleration applications. In this case, the grip force per finger would be 327 N × 2 = 654 N.
Always confirm these calculations against the manufacturer's datasheet, as gripper performance can vary. For example, Schunk provides detailed force and stroke specifications for their grippers.
How does finger length affect grip force?
Longer gripper fingers reduce the effective grip force due to increased moment. Most manufacturers provide force derating curves based on finger length. The longer the finger offset, the larger the derating, and the datasheet curve for your model is the only reliable source for the figure.
When selecting fingers, consider both the required stroke and the force derating. Shorter fingers provide higher grip force but may limit stroke. Always verify the manufacturer's derating curves for the specific gripper model.
How much stroke does a gripper need?
The gripper stroke must accommodate the part's size and any tolerance variations. The stroke must cover the full range of part sizes plus clearance to approach the part. A part with a nominal dimension of 100 mm and a ±1 mm tolerance varies over 2 mm, so the gripper must close on 99 mm and open wider than 101 mm to pass over the part. Choose a gripper whose rated stroke covers both, with margin.
Parallel grippers keep the fingers parallel through the stroke, which suits flat-sided parts and repeatable centring. Angular grippers swing the fingers through an arc, so the contact point moves, which can suit parts that need clearance to enter a cavity. Three-jaw concentric grippers are suitable for cylindrical parts, providing equal gripping force around the part's diameter.
How do pneumatic and electric grippers differ?
Pneumatic grippers provide high grip force and fast cycle times but lack precise force control and position feedback. Electric grippers offer precise force and position control, making them ideal for delicate or high-precision applications. However, they may have lower grip force and slower cycle times compared to pneumatic grippers.
Pneumatic grippers often include a spring or lock mechanism to retain grip force in case of air loss. This feature is critical for applications where power loss could result in part drop. Electric grippers typically do not have this feature, so backup power or fail-safe mechanisms may be required.
How should a gripper be mounted to a robot?
The gripper's mounting interface must align with the robot or automation system's end effector. Interface plates can be used to adapt the gripper to the robot's mounting pattern. Ensure the interface plate is rigid enough to handle the gripper's force and torque without deflection.
Cleanliness is also a consideration, especially in food or pharmaceutical applications. Stainless steel grippers and food-grade lubricants may be required to meet hygiene standards. Always verify the gripper's material and lubrication specifications against the application's cleanliness requirements.
For more detailed specifications, refer to our catalog search to find the right gripper for your application.
If you need assistance in selecting or sourcing the right grippers for your application, contact our engineering team. We can help you navigate the technical specifications and find the best solution for your needs.
What sizing mistakes affect gripper selection?
- Using the datasheet force at zero finger offset. The rated grip force is measured with the load applied close to the gripper. Real fingers are longer and shaped around the part, and the offset reduces the usable force.
- Forgetting the part's orientation. A part gripped from the side and lifted vertically relies on friction alone, so the friction coefficient matters. A part supported by a form-fit pocket in the fingers needs far less clamp force, because the fingers carry the weight rather than the friction.
- Ignoring peak acceleration. Robots stop and start hard. A payload that is safe at steady speed may see a multiple of its weight during a fast move or an emergency stop.
- Heavy fingers. Aluminium or plastic fingers keep moving mass down. Heavy steel fingers add load to the gripper and the robot and can slow the cycle.
What affects pneumatic gripper cycle time?
A pneumatic gripper's opening and closing time depends on supply pressure, tube length and diameter, valve flow and the gripper size. Long thin tubes between valve and gripper slow the motion and reduce the force built up in time. Mount the valve as close to the gripper as practical, and use flow controls if the closing speed must be limited to avoid damaging the part. A regulator holds the pressure that the force calculation assumed.
How can a gripper confirm a part is held?
Most production applications need to know that the part is present and gripped. Position sensors on the gripper detect the open and closed end positions, and a gripper with an intermediate sensor position can confirm that a part is actually between the fingers instead of the fingers closing on nothing. For electric grippers the controller reports position and force directly.
How does the environment affect gripper upkeep?
Dust, coolant, weld spatter and washdown all affect a gripper's guides and seals. Choose a sealed or protected version where the environment demands it, and follow the manufacturer's lubrication interval. Wear on the guides shows up as finger play, which affects the positioning accuracy long before the gripper stops working.
Need a quote on a specific part?
Request a QuoteFrequently asked questions
How do you calculate the grip force a gripper needs?
Grip force depends on part weight, the coefficient of friction between the fingers and the part, and dynamic forces from acceleration. Add the part weight and acceleration force, then divide by the friction coefficient multiplied by the number of fingers. A safety factor is then applied, with 2x common for horizontal applications and 3x-5x for vertical or high-acceleration ones.
What safety factor should be used when sizing a gripper?
A factor of 2x is common for horizontal applications, while higher factors of 3x-5x may be needed for vertical or high-acceleration applications. In the worked example, 327 N per finger multiplied by 2 gives 654 N per finger. The result should be confirmed against the manufacturer's datasheet, because gripper performance can vary.
How much stroke does a gripper need for a part with tolerance?
Stroke must cover the full range of part sizes plus clearance to approach the part. A part with a nominal dimension of 100 mm and a ±1 mm tolerance varies over 2 mm, so the gripper must close on 99 mm and open wider than 101 mm to pass over the part. Choose a rated stroke that covers both, with margin.
What is the difference between pneumatic and electric grippers?
Pneumatic grippers provide high grip force and fast cycle times but lack precise force control and position feedback. Electric grippers offer precise force and position control, which suits delicate or high-precision applications, though they may have lower grip force and slower cycle times. Pneumatic grippers often include a spring or lock mechanism to retain grip force if air is lost.
Industrial Automation & MRO Parts