Flush vs Non-Flush Proximity Sensor Mounting
Short answer
- Shielded (flush) inductive proximity sensors can be mounted directly in metal, while unshielded (non-flush) sensors need a clear non-metallic zone around the sensor head.
- An unshielded sensor mounted flush in a steel bracket stays permanently on, because the surrounding metal acts as a continuous target that pulls the oscillation amplitude below the trigger threshold.
- The trade-off is range: an unshielded sensor of the same diameter provides roughly 1.5 to 2 times the sensing range of a shielded equivalent, and adjacent sensors need minimum spacing to avoid mutual interference.
Installing an unshielded inductive proximity sensor flush with a metal bracket is a guaranteed way to get a permanently energized output. The distinction between shielded (flush) and unshielded (non-flush) proximity sensors comes down to how the electromagnetic field is shaped by the internal ferrite core, and ignoring that geometry leads to false triggers, shortened sensing ranges, and dead-on-arrival installations.
How does an inductive proximity sensor field work?
An inductive proximity sensor generates a high-frequency oscillating magnetic field from a coil wound around a ferrite core. When a metallic target enters this field, eddy currents are induced in the target. These eddy currents draw energy from the sensor's oscillator circuit, causing the oscillation amplitude to drop. The sensor's trigger circuit detects this drop and switches the output state.
The difference between flush and non-flush types lies entirely in the ferrite core geometry:
- Shielded (flush or embeddable) sensors have a ferrite core that wraps around the sides of the coil. This metal shield concentrates the magnetic field forward, axially out the face of the sensor. Because the field does not project laterally, the sensor body can be surrounded by metal without the surrounding material entering the sensing field.
- Unshielded (non-flush) sensors have a ferrite core that sits behind the coil. The magnetic field projects forward and radially out the sides of the sensor face. This creates a larger, deeper field, yielding a longer nominal sensing range, but it means the sensor head requires a clear zone of non-metallic material around it.
Why do unshielded sensors mounted flush stay on?
If you drill a tight-tolerance hole in a steel bracket and press an unshielded sensor into it so the face is level with the metal, the sensor will turn on and stay on. The surrounding metal bracket acts as a continuous, massive target. The eddy currents induced in the bracket draw enough energy from the oscillator to pull the amplitude below the trigger threshold permanently. The sensor cannot see through the bracket to the actual target because it is already saturated by the bracket itself.
This is a physical field interaction, not a defect. To mount an unshielded sensor in metal, you must machine a counterbore or provide a non-metallic spacer (like PTFE or Delrin) around the sensor head. The clear zone required is typically equal to the diameter of the sensor face, though you should always verify the exact free-zone dimension in the manufacturer's datasheet.
Shielded sensors avoid this entirely. You can mount them directly in a metal block, surrounded by steel on all sides, with the face flush to the surface. The internal shield prevents the lateral field from interacting with the surrounding metal. The trade-off is that concentrating the field forward physically restricts how far it can project, resulting in a shorter sensing range.
How much range do shielded sensors lose?
Because the field is compressed, shielded sensors sacrifice sensing distance. As a general rule, an unshielded sensor of the same diameter and form factor provides roughly 1.5 to 2 times the sensing range of a shielded equivalent. A standard 12mm shielded inductive sensor typically offers a nominal sensing range around 2 to 4 mm, while its unshielded counterpart might offer 4 to 8 mm.
If your target only passes 2 mm from the sensor face, a shielded sensor is the correct choice because you can mount it flush in a durable steel fixture without interference. If your target passes 6 mm away and you cannot machine a counterbore, you need the extended reach of an unshielded sensor, but you must accommodate the side clearance requirement.
How far apart should adjacent sensors be mounted?
When you mount multiple inductive sensors near each other, their oscillating fields can interact. If the fields overlap, a sensor might detect the field of its neighbor rather than a target, or the two oscillators can beat against each other causing erratic switching. This is mutual interference.
To prevent it, you must maintain minimum spacing between adjacent sensors. The rules differ based on mounting orientation:
- Side-by-side (parallel mounting): The sensing faces are pointing in the same direction, and the sensors are next to each other. For shielded sensors, maintain a center-to-center spacing of at least two times the sensor diameter. For unshielded sensors, which have wider lateral fields, maintain at least three times the sensor diameter.
- Face-to-face (opposing mounting): The sensing faces point at each other. The fields will collide directly. You must space them apart by at least six times the nominal sensing range of the sensors.
If physical space constraints prevent you from meeting these distances, you can alternate sensors with different oscillator frequencies. Manufacturers often designate specific sensors as "mutual interference protected" by assigning them alternating high and low frequencies, allowing them to be mounted close together without cross-talk.
How does target material change sensing range?
The nominal sensing range quoted on any inductive sensors datasheet is based on a standard target: a square piece of mild steel, 1 mm thick, with sides equal to the diameter of the sensing face. If your target deviates from this standard, your effective sensing range drops.
Non-ferrous metals like aluminum, brass, and copper require a correction factor. An aluminum target typically reduces the sensing range to roughly 35 to 50 percent of the nominal range, depending on the specific alloy and sensor design. Stainless steel usually operates at 70 to 85 percent of the nominal range. If your target is smaller than the sensor face or thinner than 1 mm, the effective range drops further. Always derate your expected sensing distance based on the actual target material and geometry before deciding if a shielded or unshielded type provides enough reach.
How do you choose flush or non-flush sensors?
The choice between flush and non-flush is dictated by the mechanical fixture, not personal preference. If the design calls for a flat steel plate with sensors dropped into blind holes, you must specify shielded sensors. If you need the extra range and can provide the radial clearance—either by using non-metallic mounting blocks or machining the necessary free zones—unshielded sensors will give you that extended reach.
When sourcing these components, manufacturers like Turck and IFM provide extensive families of both shielded and unshielded barrel and rectangular designs. Pay attention to the datasheet free-zone diagrams, which explicitly show the minimum non-metallic radius required around the sensor head.
If you need help cross-referencing a flush vs non-flush part number, decoding the free-zone dimensions from a datasheet, or sourcing a specific sensor form factor, our team can help you find the right match for your fixture design.
Related reading: what a proximity sensor is and the main types.
Need a quote on a specific part?
Request a QuoteFrequently asked questions
What is the difference between shielded and unshielded proximity sensors?
Shielded (flush) sensors have a ferrite core that wraps around the sides of the coil, concentrating the magnetic field forward out the face of the sensor. Unshielded (non-flush) sensors have a ferrite core that sits behind the coil, so the field projects forward and radially out the sides. That gives a larger, deeper field and longer range, but requires a clear zone of non-metallic material around the sensor head.
Why does an unshielded proximity sensor stay on when mounted flush in metal?
The surrounding metal bracket acts as a continuous, massive target. Eddy currents induced in the bracket draw enough energy from the oscillator to pull the amplitude below the trigger threshold permanently. The sensor cannot see through the bracket to the actual target because it is already saturated by the bracket itself. This is a physical field interaction, not a defect.
How much sensing range do you lose with a shielded proximity sensor?
Because the field is compressed, an unshielded sensor of the same diameter and form factor provides roughly 1.5 to 2 times the sensing range of a shielded equivalent. A standard 12mm shielded inductive sensor typically offers a nominal sensing range around 2 to 4 mm, while its unshielded counterpart might offer 4 to 8 mm.
How far apart should inductive proximity sensors be mounted?
Spacing depends on orientation. Side-by-side, shielded sensors need a center-to-center spacing of at least two times the sensor diameter, and unshielded sensors need at least three times the diameter. Face-to-face, sensors must be spaced at least six times the nominal sensing range apart. Sensors with alternating oscillator frequencies can be mounted closer together without cross-talk.
Industrial Automation & MRO Parts