Emergency Stop Devices: Requirements and Categories
Short answer
- Emergency stop functions use Stop Category 0, which removes power to the actuators immediately, or Stop Category 1, which is a controlled stop that removes power once the machine reaches zero speed; Category 2 retains power to the actuators and is not an emergency stop.
- An emergency stop device needs a red actuator on a yellow background, a mushroom or palm head, a mechanical latch that requires deliberate reset without restarting the machine, and positive-opening normally closed contacts.
- An emergency stop does not isolate a machine, so lockout/tagout with a lockable disconnect is required before maintenance.
What are emergency stop categories 0, 1, and 2?
When a machine malfunctions or an operator is in danger, hitting the E-stop must yield a predictable, safe result. The fundamental question is whether removing power immediately is the safest action, or if a controlled stop is required to prevent a secondary hazard. ISO 13850 and IEC 60204-1 define three stop categories, but only two are acceptable for emergency stop functions.
Stop Category 0 is the immediate removal of power to the actuators. The machine stops by coasting, or through mechanical braking. This is the most abrupt stop. It is acceptable for emergency stop when the inertia of the machine is low, or when maintaining power to the actuators would create a greater hazard. For high-inertia rotating equipment, a Category 0 stop might cause the load to coast for an unacceptable distance, but it remains the fail-safe default when the control system cannot be trusted to execute a controlled stop.
Stop Category 1 is a controlled stop where power remains available to the actuators just long enough to bring the machine to a standstill. Once the machine reports zero speed, power is immediately removed. This is the most common emergency stop category for high-inertia machinery, such as large conveyors or centrifuges, where a sudden power loss could cause extended coasting, product spillage, or mechanical damage from rapid deceleration. The safety logic must monitor the speed; if the machine does not reach zero speed within a defined time window, the safety circuit must force a Category 0 stop.
Stop Category 2 is a controlled stop where power is retained to the actuators after the machine has stopped. Category 2 is not an emergency stop. It is a functional stop, used for normal machine pauses or door-controlled safe停. An emergency stop must ultimately remove power from the hazardous actuators to guarantee that a single point of control failure cannot restart the machine unexpectedly.
What characteristics must an emergency stop device have?
An emergency stop device is not just a standard pushbutton wired into a PLC input. It must meet specific mechanical and electrical standards to ensure it functions when needed, even after years of neglect or in harsh environments. When sourcing emergency stop devices, you must verify compliance with these mandatory characteristics.
The actuator must be red on a yellow background. This high-contrast color scheme is mandated by ISO 13850 to ensure the E-stop is visually distinct from all other machine controls. The background must be yellow, and the actuator itself must be red. A red button on a black or grey panel does not meet the standard.
The actuator must be a mushroom or palm head design. This shape allows the operator to strike the button with the palm of their hand or fist from multiple angles, ensuring rapid actuation even if their hand position is awkward or they are off-balance. A standard flush pushbutton is unacceptable for an E-stop function.
The device must latch mechanically upon actuation. It must require a deliberate, intentional action to reset—typically a twist (turn to release), pull (pull to release), or key release. A momentary button that resets itself when the operator removes their hand is strictly forbidden. Furthermore, the reset action must only physically reset the switch; it must never automatically restart the machine. Restarting requires a separate, deliberate cycle-start command.
Electrically, the E-stop must use positive-opening normally closed (NC) contacts. This means the contact mechanism is physically forced apart by the movement of the actuator, rather than relying on a spring to open a normally open (NO) contact. If the contacts weld together due to an electrical fault, the mechanical action of pushing the E-stop will physically break the weld or tear the contact carrier, ensuring the safety circuit opens. These devices must also be safety relays and controllers capable of detecting contact welds via dual-channel monitoring.
How do rope-pull switches work on conveyors?
On long conveyors, it is impractical to place a mushroom E-stop within reach of every point along the belt. Rope-pull switches solve this by running a tensioned cable along the length of the conveyor. An operator can grab and pull the cable from anywhere along its length to actuate the stop. These switches must meet specific criteria beyond those of a standard E-stop button.
The switch must actuate if the cable is pulled in either direction. If the cable is pulled away from the switch, the mechanism trips. If the cable is pushed toward the switch, causing it to slacken, the mechanism must also trip. This is critical because a slack cable could indicate a broken cable, a detached anchor, or a mechanical failure that would render the system inoperable when needed.
To ensure the switch detects both tension and slack, the cable must be properly tensioned during installation, and the switch must monitor that tension. Most modern rope-pull switches include a tension indicator window or a tension adjustment mechanism. The safety circuit must monitor the state of the cable tension. If the cable stretches over time or breaks, the switch must detect the loss of tension and trip the safety circuit, requiring maintenance to re-tension or replace the cable before the conveyor can run.
Placement and reachability are critical. The cable must be accessible along the entire length of the conveyor. It should be positioned so that an operator who is caught, entangled, or falling can reach the cable. The maximum distance between supports for the cable is determined by the manufacturer, but typically, the cable should not sag more than a few centimeters between supports to ensure a positive actuation force is transmitted to the switch.
Where must emergency stop devices be placed?
Each machine must have at least one E-stop accessible at every operator control station. On large machines, multiple E-stops may be required. The rule of thumb is that an operator must be able to reach an E-stop within a few steps from any position where they interact with the machine. If the machine has multiple entry points or operating zones, each zone must have its own E-stop.
When designing or retrofitting control stations, consider the physical environment. An E-stop located behind a door or inside a panel is useless in an emergency. The device must be mounted at a height that is reachable by most operators, typically between 0.6 and 1.8 meters from the floor. It must not be obstructed by materials, tools, or other equipment.
For mobile equipment or machines with moving parts, the E-stop must be accessible from the ground. If the machine has a platform or cab, the E-stop must be accessible from that platform. If the machine has multiple levels, each level must have an E-stop.
Is an emergency stop the same as safe isolation?
An emergency stop is not a lockout/tagout (LOTO) device. This distinction is critical for maintenance safety and is often misunderstood.
The emergency stop function is designed to prevent a dangerous situation from escalating during normal operation or an unexpected event. It removes power from the actuators (after a controlled stop if Category 1) to halt the hazardous motion. However, the safety circuit itself remains energized, and the main disconnect may still be closed. The machine is stopped, but it is not electrically isolated.
Safe isolation, or LOTO, is the procedure required before performing maintenance. It involves opening the main electrical disconnect, physically locking it in the open position with a padlock, and verifying the absence of voltage at the actuators. An E-stop button does not achieve isolation. A machine can be restarted by resetting the E-stop, which would be catastrophic if a technician is inside the machine. Safe isolation requires a dedicated isolation switch, typically a rotary disconnect with a lockable handle. Never use an E-stop device as a substitute for lockout/tagout.
When specifying safety components from manufacturers like Schneider Electric, ensure you are selecting the correct device for the correct function. E-stops are for operator safety during operation; disconnects are for maintenance safety.
If you need help sourcing compliant E-stop devices, rope-pull switches, or safety relays, or if you need to cross-reference a specific component, our team can help you find the right parts for your application.
Related: Pushbuttons, Selector Switches and Pilot Lights.
Also on this topic: Cable-Pull Safety Switches: Rope Pull Explained.
Need a quote on a specific part?
Request a QuoteFrequently asked questions
What is the difference between Stop Category 0, 1, and 2?
Stop Category 0 removes power to the actuators immediately, so the machine coasts or stops through mechanical braking. Stop Category 1 is a controlled stop that keeps power available just long enough to reach zero speed, then removes it. Stop Category 2 retains power to the actuators after the machine has stopped, so it is a functional stop and is not acceptable as an emergency stop.
What color and shape must an emergency stop button be?
The actuator must be red on a yellow background, as ISO 13850 mandates, so it stands out from all other machine controls. A red button on a black or grey panel does not meet the standard. The actuator must also be a mushroom or palm head design, because a standard flush pushbutton is unacceptable for an emergency stop function.
How do rope-pull switches work on conveyors?
A rope-pull switch runs a tensioned cable along the length of the conveyor, so an operator can pull it from anywhere along the belt to stop the machine. The switch must trip when the cable is pulled in either direction, and it must also trip when the cable slackens, because slack can indicate a broken cable or a detached anchor.
Can an emergency stop be used instead of lockout/tagout?
No. An emergency stop halts hazardous motion, but the safety circuit stays energized and the main disconnect may still be closed, so the machine is not electrically isolated. A machine can be restarted by resetting the E-stop, which would be catastrophic if a technician is inside. Safe isolation requires opening the main disconnect, locking it with a padlock, and verifying the absence of voltage at the actuators.
Industrial Automation & MRO Parts